
Reporting cutoff: October 22, 2026, 2:22 p.m. EDT (6:22 p.m. UTC). Every vendor and advisory page linked below was reopened and confirmed at that time. The underlying vulnerability is old and stable; the vendor menu paths are what age, so re-check them on your own hardware.
If your router still has Wi-Fi Protected Setup turned on, turn it off — even if you never use it. WPS is the button-and-PIN shortcut that was supposed to make joining a home Wi-Fi network easier. It has a design flaw that lets someone nearby guess the PIN and walk onto your network. The weakness was documented publicly in 2011 and was never patched out of the standard, because the flaw is in the standard itself.
The practical problem for a home or small business is not that this is a dramatic new attack. It is that most routers ship with WPS enabled, most owners never think about it, and the setting is buried several menus deep in an interface nobody opens after install day. Meanwhile the network sits there holding bank logins, payroll files, medical portals, cameras, and point-of-sale terminals.
What WPS is, and why it exists
WPS is a Wi-Fi Alliance standard built around one idea: joining an encrypted network should not require typing a long password into a phone. Instead, you either press a physical button on the router and the device within two minutes, or you type an eight-digit PIN printed on a label. Both methods hand the device the network credentials automatically.
The convenience is real. It is also the entire problem, and CERT/CC named it plainly: “By design this method is susceptible to brute force attacks against the PIN.” The PIN method is not just weaker than typing a password. It is weaker in a specific, measurable way.
Figures as published by CERT/CC and CISA. The reduction from 100 million to 11,000 is the whole vulnerability.
Why the eight-digit PIN is not really eight digits of security
Three separate design details stack up. CERT/CC explains each one in its advisory on the flaw:
- The router confirms your guesses. When the PIN is wrong, the access point sends an EAP-NACK message back — and those messages are sent in a way that lets an attacker tell when the first half of the PIN is correct.
- The last digit is not secret. It is a checksum, so the last digit of the PIN can be derived rather than guessed.
- There is often no lockout. CERT/CC reports that many wireless routers implement no lockout policy at all, and some reportedly required a reboot after a brute-force attempt.
Those three facts are why CERT/CC could state the math so bluntly: “The number of attempts goes from 10^8 to 10^4 + 10^3 which is 11,000 attempts in total.” CISA’s 2012 alert put a time on it — freely available tools recover a WPS PIN in four to ten hours — and named the blast radius: “Once on the network, the attacker can monitor traffic and mount further attacks.”
The setting that lies to you
CISA’s alert carries a warning worth reading twice before you close the admin page and walk away:
“Note that some access points may not actually disable WPS when the web management interface indicates that WPS is disabled.”
Practically, that means the checkbox is not proof. Confirm by leaving WPS off and watching the physical WPS button’s behavior, or by having your IT provider verify it. On an ISP-supplied gateway you may not have access to that menu at all, which is a separate and common problem — see the good and bad table below.
Are you affected?
Likely affected if any of these are true:
- Your router has a physical WPS button, or a WPS/Wi-Fi Protected Setup option visible somewhere in its admin interface.
- You bought the router in the last decade — WPS was near-universal on consumer and small-business hardware from roughly 2010 through 2018.
- You rented the router from a cable or telecom provider and never signed into the advanced settings.
Probably not affected if:
- Your admin interface has no WPS option and no WPS button exists on the case.
- You already disabled it, or your ISP replaced it with newer managed hardware that no longer exposes WPS.
Absence of the setting is not proof of absence of the feature on every firmware build. Treat probably not affected as a lower risk, not a guarantee.
Turn WPS off: the ordered steps
Work from a device already connected to that network — ideally by Ethernet — so you do not cut your own wireless access mid-change. Before you start, this is exactly the kind of change worth capturing first: if something goes wrong you will want the current settings to put back.
Log in to the router admin page
Use the address from the router label or your provider’s documentation rather than guessing. For NETGEAR, the vendor’s support documentation directs you to http://www.routerlogin.net or http://www.routerlogin.com.
Find the WPS setting — the labels are inconsistent
CERT/CC’s workaround section is the honest answer here: “Depending on the vendor, this may be labeled as external registrar, router PIN, or WiFi Protected Setup.” Look under wireless, Wi-Fi, advanced setup, system tools, or security. You are looking for one of those three names.
Turn it off, and save
On TP-Link, the vendor’s own guidance is a specific path: “To enable or disable WPS, go to System Tools > System Parameters > WPS in the router’s web interface and check or uncheck the Enable WPS checkbox.” NETGEAR’s own support article uses a different route — Advanced Setup, then Wireless Settings, then a Disable Router’s PIN checkbox. Same setting, different names, which is exactly why guessing from memory fails.
Do not accidentally replace your wireless settings
NETGEAR’s documentation carries a specific warning about a nearby checkbox: if you clear Keep Existing Wireless Settings, the router’s wireless settings change to an automatically generated random SSID and security key the next time a client uses WPS — which would drop every device that joins by name. Leave it selected. NETGEAR recommends exactly that.
Do not use the router button to disable it
TP-Link warns that pressing the WPS button for more than five seconds will disable the wireless function on the router. If you are trying to turn wireless off as part of this task, that is a different project with a different outcome. This task is about turning the WPS feature off while your Wi-Fi keeps working.
Reconnect anything that was relying on WPS
If a printer, camera, or older phone only ever joined by WPS, it will now need the Wi-Fi password typed in once. Have the password ready before you disable anything. If you are not sure what uses WPS, disconnect one device at a time and reconnect it by password — that is the test.
Change the Wi-Fi password while you are there
Turning off WPS closes a door. If your router still uses its factory default Wi-Fi password or a weak one, that door is still wide open. Change it, and change the router admin password too.
If you still need WPS for one device
Sometimes there is a real dependency — an older printer with no password-entry screen, for instance. NETGEAR’s guidance is to use the push-button method rather than the PIN, supervise it, connect one device at a time, and disable WPS immediately afterward. Treat it as a temporary tool with an expiry, not a permanent setting.
NETGEAR’s own security guidance is blunt about the direction of travel: “To enhance security, many modern routers, including NETGEAR models, have WPS turned off by default. If you need to use it, you can temporarily enable WPS, but it’s recommended to disable it again immediately after use.” And on whether to turn it off entirely, the same source answers directly — “For maximum security, yes. If you exclusively use your router’s app or QR code for setup, disabling WPS in your router’s settings is the safest option.”
Good
- Disable WPS in the admin interface, then save and confirm.
- Use the push-button method for a legacy device, then turn WPS back off.
- Back up the router configuration before you change anything.
- Change the Wi-Fi password and the admin password in the same session.
- Give a guest network to visitors instead of handing out the main password.
Bad
- Leaving WPS on because you do not currently use it.
- Holding the WPS button for five-plus seconds to “turn it off” — that kills wireless entirely.
- Clearing Keep Existing Wireless Settings and silently renaming your network.
- Disabling WPS over a wireless connection you depend on.
- Assuming the checkbox being unchecked proves the feature is off.
Two examples
Harmless failure: the network that vanished
A home office clears Keep Existing Wireless Settings while disabling WPS. Every phone, camera, and smart device still shows the old network name, but nothing can reconnect — and the router now broadcasts a newly generated name nobody has written down. Recovery is straightforward: use the push button on a laptop, join the new name, and reconfigure the devices. Annoying, not costly. This is why step four exists.
Costly wrong turn: the button held too long
A small business with a front-desk tablet and card terminals tries to turn WPS off by holding the WPS button “until it blinks.” TP-Link’s documentation states that holding it more than five seconds disables the wireless function. Wireless goes down in a busy shop; the tablet and terminals drop; the fix requires a physical cable to the router. The setting they needed was one menu deep, not one button long.
If you suspect someone already used WPS
Do not start by factory-resetting anything — you would destroy the evidence and the configuration. Work outward instead:
- Change the Wi-Fi password. Every previously-authorized device must rejoin, which is the point.
- Change the router admin password.
- Review the connected-device list and remove or block anything you cannot identify.
- Update the router firmware.
- Disable WPS so it cannot be used as a second way in.
Note the asymmetry here. A strong Wi-Fi password does not help if the WPS PIN is still enabled, because recovering the PIN is a path to the password. That is the whole point CERT/CC’s math was making.
Frequently asked questions
Is WPS the same thing as the Wi-Fi password?
No. They are two different ways into the same network. The Wi-Fi password is a shared secret you type. The WPS PIN is a second, shorter secret that hands a device the same credentials automatically — and the shorter secret is the one that can be guessed. CERT/CC rates the WPS PIN method as susceptible to brute force by design.
Can an attacker use WPS if I am not on Wi-Fi right now?
CISA’s alert scopes it to radio range: an attacker within radio range of the access point can brute-force the PIN, then obtain the WEP or WPA passwords and likely gain access. This is a local-proximity attack, not an internet-reachable one. A strong Wi-Fi password still matters — it is what the attacker is trying to recover — but WPS weakens the entry point that would otherwise require guessing it.
My ISP router has no WPS option. Am I safe?
You are in better shape than most, because many managed ISP gateways do not expose advanced settings to customers. That also means you may not be able to change other settings yourself. If you want certainty, ask your provider whether the gateway exposes WPS, or consider a router you control.
Will disabling WPS break my smart-home devices?
Possibly, if one of them was paired by WPS and cannot accept a typed password. That is the dependency described earlier. Reconnect it once by password while you are logged in to the router, and it will keep working.
Does firmware update fix this?
CISA’s 2012 alert listed two remedies: update firmware, and disable WPS. Because the flaw is in the WPS specification itself, CERT/CC noted at the time that it was unaware of a practical fix and recommended the disable workaround. Updating firmware is still worth doing for other reasons. But disabling the feature is the step that addresses this specific weakness.
Which vendors were listed as affected?
CERT/CC’s vendor list marked Belkin, Buffalo, Cisco Systems, D-Link Systems, Linksys, Netgear, TP-Link, Technicolor, and ZyXEL as affected. That list is from 2011 and reflects vendor statements then, not a current model-by-model inventory.
What we do not know
Two limits are worth stating plainly rather than glossing over. First, we did not test your specific router, and the label a vendor uses for WPS varies by model and firmware build — treat the vendor paths above as a starting point, not a guarantee for your hardware. Second, CERT/CC’s affected-vendor list and both advisories are historical documents from 2011–2013; we are citing them because the design flaw is unchanged, not because they describe current firmware.
One practical next step
Log into your router tonight and find the WPS setting. It takes about five minutes, it requires no purchase, and it closes the one flaw on your network that a stronger password cannot fix. If you want the settings captured first — which we recommend — our router configuration backup checklist walks through that before you touch anything.
Related IT Guys guides
- Quick Tech Tip: Check Your Router Before It Becomes the Weak Link — the broader twenty-minute baseline this belongs to. WPS is one line in that checklist; this article is the depth behind it.
- Put Guest Wi-Fi and Smart Devices on Their Own Network — the other half of router hygiene, and the right answer to handing out your main password.
- Back Up Your Router or Firewall Configuration Before You Need It — capture current settings before changing any of them.
- TP-Link CVE-2026-3227: How to Check Specific TP-Link Router Models — a different router risk, specific models, separate patch.
- Wi-Fi Fast by the Router but Slow Elsewhere? — the performance-side diagnostic, when the problem is speed rather than access.
- Printer or Camera Keeps Going Offline? — what to do when a device that used WPS needs a stable address instead.
Sources
- CERT Coordination Center, Vulnerability Note VU#723755, “WiFi Protected Setup (WPS) PIN brute force vulnerability.” kb.cert.org/vuls/id/723755. Published December 27, 2011; last revised May 10, 2012. Source of the design-flaw description, the 11,000-attempt reduction, the EAP-NACK and checksum explanations, the absence of lockout policy on many routers, the disable-WPS workaround, and the affected-vendor list.
- CISA, Alert TA12-006A, “Wi-Fi Protected Setup (WPS) Vulnerable to Brute-Force Attack.” cisa.gov. Last revised January 23, 2013. Source of the four-to-ten-hour recovery figure, the impact statement about monitoring traffic and mounting further attacks, the firmware and disable-WPS remedies, and the warning that some access points may not actually disable WPS when the interface says they have.
- TP-Link, “WPS Button: How to Use It on a TP-Link Router.” tp-link.com/us/support/faq/2656. Source of the System Tools > System Parameters > WPS menu path and the Enable WPS checkbox, the five-second button warning, and the iOS and WEP limitations.
- NETGEAR, “How do I specify WPS settings on my Nighthawk router?” kb.netgear.com/24103. Source of the routerlogin.net and routerlogin.com admin addresses, the Advanced Setup > Wireless Settings path, the Disable Router’s PIN checkbox, and the Keep Existing Wireless Settings warning.
- NETGEAR, “What Is WPS on a Router? Setup, Security & NETGEAR Tips.” netgear.com/hub/network. Source of the recommendation to prefer the push-button method, to disable WPS immediately after use, and to turn it off entirely for maximum security.
